Pedal Commander for SsangYong Rexton: Installation Guide

By Pedal Commander® - The Best Throttle Response Controller | Published: 2026-10-26

Category: How-to Guides

Learn how to install the Pedal Commander throttle response controller on your SsangYong Rexton. This guide covers preparation, connection, and initial setup to reduce throttle lag and improve acceleration.

Quick answer

Installing the Pedal Commander on your SsangYong Rexton takes about 15 minutes and requires no special tools. Simply locate the throttle pedal connector, plug in the device, mount the control module, and select your preferred driving mode.

Why install a throttle response controller on your Rexton?

Many SsangYong Rexton drivers notice a slight delay when pressing the accelerator, especially in city traffic or when merging onto highways. This throttle lag is a common characteristic of modern drive-by-wire systems. The Pedal Commander reduces that delay by amplifying the pedal signal, giving you a more immediate and responsive acceleration feel without altering your engine's power output or voiding your warranty.

Choosing the correct version for your Rexton

The Pedal Commander is designed to fit specific generations of the SsangYong Rexton. It supports the 1st Gen Facelift (2007-2017) with various engine options including 2.3L, 2.8L, 3.2L, 2.0L, 2.2L diesel, 2.7L diesel, or 2.9L diesel, as well as the 2nd Gen (2017+) with 2.0L turbo or 2.2L diesel. When ordering, make sure to select the option that matches your vehicle's year and engine to ensure a proper fit.

Installation steps

1. Locate the throttle pedal connector: Under the dashboard on the driver's side, find the electrical connector attached to the top of the accelerator pedal. It is usually a rectangular plug with a locking tab. Gently press the tab and pull the connector straight out to disconnect it. Do not pull on the wires; always grip the connector body to avoid damaging the pins.
2. Connect the Pedal Commander inline: Take the Pedal Commander's wiring harness and plug the male end into the pedal socket (where you just removed the original connector). Then plug the original connector into the female end of the Pedal Commander harness. Ensure both connections click firmly into place. If the connectors do not seat fully, check that you have the correct version for your Rexton. A loose connection can cause intermittent response.
3. Mount the control module: Peel the backing from the included adhesive pad and attach the Pedal Commander control module to a clean, dry surface under the dash where it is within easy reach but does not interfere with your feet or pedals. A common spot is on the side of the center console or the lower dash panel. Test that the module does not block your knee or get kicked during driving before finalizing the mount.
4. Power on and select your mode: Start the engine. The Pedal Commander screen will light up. Use the +/- buttons to cycle through modes: Eco (for fuel savings), City (for normal driving), Sport (for sharper response), and Sport+ (for maximum response). Press the center button to confirm your selection. Start with City mode and drive for a few days before trying Sport. The difference can feel abrupt if you switch directly from stock.
5. Adjust the response level: Within each mode, you can fine-tune the response using the +/- buttons (usually 1-9 levels). Lower numbers give a milder effect; higher numbers provide more aggressive throttle response. Adjust until the acceleration feels natural for your driving style. If you notice jerky starts, reduce the level by 1-2 steps. The ideal setting balances responsiveness with smoothness.

Product details

Pedal Commander for SsangYong Rexton: Fits SsangYong Rexton 1st Gen Facelift (2007-2017) with 2.3L, 2.8L, 3.2L, 2.0L, 2.2L diesel, 2.7L diesel, or 2.9L diesel, and 2nd Gen (2017+) with 2.0L turbo or 2.2L diesel. You must select the correct version for your Rexton's generation and engine to ensure the connector matches and the device works properly.
Pedal Commander for SsangYong Rexton